103 www.victronenergy.com Victron Energy B.V. | De Paal 35 | 1351 JG Almere | The Netherlands E-mail: sales@victronenergy.com | www.victronenergy.com Cerbo GX Cerbo-S GX Supply voltage 8 – 70 VDC Power draw without GX Touch 2.8 W @ 12 V Power draw with GX Touch Backlight off: 3.8 W @ 12 V Backlight at max: 4.8 W @ 12 V Mounting Wall or DIN rail (35 mm) (2) Communication ports VE.Direct ports (always isolated) 3 (max. possible VE.Direct devices: 15) (3) VE.Bus (always isolated) 2 paralleled RJ45 sockets VE.Can yes - non isolated BMS-Can port Yes No Bluetooth Yes (4) IO Resistive tank level inputs 4 0 Temperature sense inputs 4 0 Digital Inputs 4 4 Relays(5) 2 x NO/NC DC up to 30 VDC: 6 A DC up to 70 VDC: 1 A AC: 6 A, 125 VAC Other Outer dimensions (h x w x d) 78 x 154 x 48 mm Operating temperature range -20 to +50 °C IP Rating IP20 Standards Safety IEC 62368-1 EMC EN 301489-1, EN 301489-17 Automotive ECE R10-6 GX Touch 50 / GX Touch 70 Mounting With included mounting accessories Protection cover Included with every GX Touch from serial number HQ2242 Can also be purchased individually: Part # BPP900462050: GX Touch 50 protection cover Part # BPP900462070: GX Touch 70 protection cover Display Resolution GX Touch 50: 800 x 480 GX Touch 70: 1024 x 600 IP Rating IP54 (without connectors) Other Outer dimensions (h x w x d) GX Touch 50: 87 x 128 x 12.4 mm GX Touch 70: 113 x 176 x 13.5 mm Cable length 2 meter Notes 1. For more detailed information about the Cerbo GX and the GX Touch, please visit the Victron GX product range page at Victron live: www.victronenergy.com/live/venus-os:start 2. DIN rail mounting requires an additional accessory - DIN35 adapter small. 3. The listed maximum in above table is the total connected VE.Direct devices such as MPPT Solar Charge controllers. Total means all directly connected devices plus the devices connected over USB. The limit is mostly bound by CPU processing power. Note that there is also a limit to the other type of devices of which often multiple are connected: PV Inverters. Up to three or four three phase inverters can typically be monitored on a CCGX. Higher power CPU devices can monitor more. 4. Bluetooth functionality is intended to be used to assist with initial connection and networking configuration. You cannot use Bluetooth to connect to other Victron products (e.g. SmartSolar charge controllers). 5. In Cerbo GX hardware there are two relays. Currently, Relay 1 can be used for programming as an alarm relay, generator start/stop, tank pump, temperature-controlled relay or manual operation. Relay 2 is available for programming as a temperature-controlled relay or manual operation in the Relay menu of the GX (requires firmware 2.80 or higher). DIN35 adapter small DIN-Rail adapter to easily mount a device on a DIN-Rail. Suitable for the Cerbo GX. GX Touch adapter for CCGX cut-out This adapter is designed to easily replace the CCGX display with the newer GX Touch 50 or the GX Touch 70. Contents of the packaging are the metal bracket, the plastic bezel, and four mounting screws. Temperature sensor for Quattro, MultiPlus and GX Device (such as the Cerbo GX) Accessories included with the GX Touch Optional accessories
RkJQdWJsaXNoZXIy MjM2MTk=