100 SERIES ACTUATORS & HATCH LIFTS 53 lencomarine.navico.com 12 Volt Models Approximate Stroke Approximate L.O.A. Retracted Approximate L.O.A. Extended Superseded Part # Part # 4" (10.1 cm) 15" (38.1 cm) 19" (48.3 cm) HL-400 20760-001 6" (15.2 cm) 20" (50.8 cm) 26" (66.0 cm) HL-600 20762-001 8" (20.3 cm) 20" (50.8 cm) 28" (71.1 cm) HL-800S 20764-001 8" (20.3 cm) 24" (60.9 cm) 32" (81.2 cm) HL-800 20766-001 12" (30.5 cm) 24" (60.9 cm) 36" (91.4 cm) HL-1200S 20768-001 12" (30.5 cm) 29" (73.7 cm) 41" (104 cm) HL-1200 20770-001 16" (40.6 cm) 29" (73.7 cm) 45" (114 cm) HL-1600S 20774-001 16" (40.6 cm) 33" (83.8 cm) 49" (124 cm) HL-1600 20776-001 20" (50.8 cm) 33" (83.8 cm) 53" (134 cm) HL-2000S 20778-001 20" (50.8 cm) 37" (93.9 cm) 57" (144 cm) HL-2000 20780-001 24" (60.9 cm) 37" (93.9 cm) 61" (154 cm) HL-2400S 20782-001 24" (60.9 cm) 41" (104 cm) 65" (165 cm) HL-2400 20784-001 26" (66.0 cm) 47" (119 cm) 73" (185 cm) HL-2600 20786-001 30" (76.2 cm) 47" (119 cm) 77" (195 cm) HL-3000 20788-001 24 Volt Models Approximate Stroke Approximate L.O.A. Retracted Approximate L.O.A. Extended Superseded Part # Part # 4" (10.1 cm) 15" (38.1 cm) 19" (48.3 cm) HL-400/24V 20761-001 6" (15.2 cm) 20" (50.8 cm) 26" (66.0 cm) HL-600/24V 20763-001 8" (20.3 cm) 20" (50.8 cm) 28" (71.1 cm) HL-800S/24V 20765-001 8" (20.3 cm) 24" (60.9 cm) 32" (81.2 cm) HL-800/24V 20767-001 12" (30.5 cm) 24" (60.9 cm) 36" (91.4 cm) HL-1200S/24V 20769-001 12" (30.5 cm) 29" (73.7 cm) 41" (104 cm) HL-1200/24V 20771-001 16" (40.6 cm) 29" (73.7 cm) 45" (114 cm) HL-1600S/24V 20775-001 16" (40.6 cm) 33" (83.8 cm) 49" (124 cm) HL-1600/24V 20777-001 20" (50.8 cm) 33" (83.8 cm) 53" (134 cm) HL-2000S/24V 20779-001 20" (50.8 cm) 37" (93.9 cm) 57" (144 cm) HL-2000/24V 20781-001 24" (60.9 cm) 37" (93.9 cm) 61" (154 cm) HL-2400S/24V 20783-001 24" (60.9 cm) 41" (104 cm) 65" (165 cm) HL-2400/24V 20785-001 26" (66.0 cm) 47" (119 cm) 73" (185 cm) HL-2600/24V 20787-001 30" (76.2 cm) 47" (119 cm) 77" (195 cm) HL-3000/24V 20789-001 Optional Hatch Lift Accessories Stainless Steel Pull Pin Clamshell packaged. 60101-001D Stainless Steel Non-locking Slide Bracket For hatch lifts. In case of power failure, this bracket allows you to pull the hatch open a minimum of 5" (12.7 cm) in order to remove bolt for access. Non-retail box. 70381-001 Hatch Lift Rocker Switches 12 & 24 Volt Rocker Switch for hatch lifts with two 30" non-terminated power leads. This switch is CE certified and ABYC compliant. It is also 20A rated and clam shell packaged. 15096-001 15098-001 Single Hatch Lift Dual Hatch Lift 45 MAX 45 MAX Hatchlift YLength IN/CM XLength IN/CM WLBS/KG YxW÷X=Force Lenco Hatch Lift Mounting 1. Follow the chart to the right to figure out load on the hatch lift. Maximum load is 500 lbs (226.8 kg). Y = Total length of hatch X = Length from the hinge to the hatch lift mounting point W = Weight of the hatch to be lifted 2. Determine the angle of the hatch lift mount. Do not exceed 45 degrees from center. 3. Mount the hatch lift on the desired location as per the above instructions. Important: It may be necessary to shim the upper or lower mounting bracket up or down so the hatch does not bind when fully closed. The hatch lift does not stop pulling until it has reached its fully closed position. If the hatch fully closes before the hatch lift is fully retracted, it will cause damage to the lift or the mounting hardware. Shim the hatch lift with stainless washers for small amounts of length. Use Lenco shim part #50015-002D for lengths greater than 1/8" (3.2 mm). 4. Wire to switch according to the hatch lift wiring diagram in manual. 6.25" (15.9 cm)
RkJQdWJsaXNoZXIy MjM2MTk=